Видео

Nice work! Zero seams is still better and worth the extra time. Plus when you have that many miters coming together you overdose on endorphins and dopamine when it all comes together

If you’re miter folding plywood use a track saw! You don’t have to worry about the imperfections in the plywood not providing you a clean rip like you do on a table saw. A track will bow with the wood and if it’s crooked or out of square you can easily account for that too. Pushing a big awkward 8 foot sheet of plywood is physically much more work than pushing a track saw as well.

The ONLY thing I care about in a sander is what can remove material faster. Compared to the 5 inch variable speed DeWalt for under $100, does the festool do anything more? Does it spin significantly faster or vibrate more?

good job,like

Why’d you quit RUclips? Love your channel and I hope you come back!

Floating shelves should be thin. Look at the shelves of a standard bookshelf. 3/4” or 1” max. Bigger than that and you are making a mantle.

Doesn’t have to be an expensive SawStop..k. Revenue a cheaper One will work. Get a beginner Skill portable. Only couple hundred…it will do a great job…

How is this holding up three years later ?

Thoughts on the Woodpeckers StealthStop thus far? I just got mine in preparation for finishing my miter station. All 4 of the red stops had micro cracks in them out of the package. Basically from the set screw to the end of that section. Have you had any issues?

how are the shelfs attached to the brackets?

Pinch Dogs are good, but another way is to pre-assemble one entire run using the Kreg jig.

The only issue with adding baseboard to Wainscotting is where it meets the door casing and unless you have added a back band to the casing, it doesn't really work.

Sorry, but that product is wayyy over priced.

very impressed dude..nice job!!!

Nice. Good job man!

Nice video.

Very nice! 🫵

I have an old building, roughly 75-80 yrs old. When there is a saturating rain and ground is saturated, water will come up through the concrete floor and then will leave the same way. Question is, can that be repaired by covering it with a coat of thin concrete or does it have to be taken out and replaced with new? I’m looking for a cost effective way to fix it. Thanks

Valve is useless buried in the wall.

amature

Thanks for the tips, great video! I was wondering if you have any experience with using rubio on softwoods like speuce or pine? That what my project is made of and I've seen a complaint on reddit about rubio causing uneven staining quite easy.

The music is overpowering

Looks great Jordan, the only thing I would say is the laminate on your track needs to be beveled to the height of the track. That’s a catching point if you slide timber that’s slightly bowed. Nice job 👌🏻🇦🇺

Is it possible to do this with a hand router, or you really need the stability of a router table?

great video

I don’t think this is the way to do it. You did not apply the upper coat. There are two different coatings done with two different products.

Do you have plans for sale?

I am looking at trying out the Stealth Stop system too. How close to the thickness of the 1/2 inch MDF is the track? Did you find not having a piece of laminate under the track to be an issue or did you prefer having the track recessed a bit instead of flush?

How long of a working time does the Rubio have once the 2 parts are combined?

I don't see why you are getting so much hate. I do believe festool is overcharging for their system design but i also can see that they are slightly more convenient than anyone else which is why if i sanded for a living or sanded regularly i would definitely invest in it even if it's a bit of a robbery.

I understand. Festool is good for all RUclipsrs.

Thank you..

Thank you Mr Jordan

I want to treat. White oak cabinets but dont want the raw colour of the eood to change! Which product will be best to use?

I've been a builder all my life but over 50 homes and learned all the trades, l laugh at these people making vedios, like this guy

Yeah sooooo easy!!!!…..all I need to do is build myself a fully decked out work shop…… soooo simple

Nice build I feel like that reciprocal was pretty high

The maintenance oil only comes in 3 options. White, black, or pure. How do you know which one to get?

I agree with you on the drum sander. I've used mine four times and had the same issues and frustrations you mentioned. I want to sell mine too. What did you sell yours for (ballpark)? #totaltegrettool

I have that claw horse and I only ides it once! Total waste

I loved your floating shelf but the finish you chose seemed a lack luster. Hope you liked it. I appreciated all the info in this short video. Tks

Wow!! U amke it look so easy

is there a finish....the best part...lol

You're a ninja, amazing job! #goals

You said the ratio of 1:2 vs 1:3 doesn't matter. Sorry, but that is incorrect. The ratio hugely affects curing time.

I don't see the point in using both.

😮

Young man. You know , what you are doing. Lovely equiipment in your workplace. Big envy. .

Love the concept and design. I plan to try this out on a small shelf for my son's room to keep his Xbox. If it works, I will build 4 large ones for my fireplace built-ins.

I am little confused. Where did you put the filters on the front or on the back of the fan?